3d Maxpider Remove Logo (Must Know Things)
Maxpider floor mats are high-quality mats that add beauty to a vehicle’s cabin.
Suppose the 3d logo on the mat is large and looks out of place. You can remove this logo and install the one you prefer. This article will tell you how to remove the logo.
You can remove the 3d logo on Maxpider floor mats by using diagonal nippers. The removal might leave two small holes in the floor mat. Fill the holes with glue to make a better appearance.
Why Remove 3d Maxpider Logo?
The 3d Maxpider floor liners logo looks unappealing and out of place. There is no need for the large chrome logo to be there.
The 3d logo is obnoxious and can be distracting whenever your heel bumps into it.
Altogether the logo’s presence is a bit annoying as it ruins an otherwise excellent floor mat.
Having a raised section of the floor mat with the words on it would be a better design.
The color should also be black so that it won’t look odd and different from the rest of the mat.
How to Remove 3d Maxpider Logo?
Removing the 3d Maxpider logo requires prying off the metal buttons attached to the aluminum logo.
To remove the logo, take out the mat and turn it over to see the metal buttons holding the logo.
You’ll need a plier or other pry tool to tear off the metal buttons under the mat. You can purchase a plier here.
Use the plier or a similar tool to tear off the metal buttons from the mat.
The logo will fall off, and two holes will appear where the buttons go through the mat. Use glue to fill up the holes.
You can apply a black sharpie atop the glue to match the mat’s color.
If you’d like to replace the logo with another one of your choices, you’ll need a few items.
- New logo, maybe Tesla logo or any one of your choice.
- Epoxy for gluing the new logo.
- Pliers
- Paper towel or anything to wipe up epoxy spills and runs.
- Latex gloves
- Surface for mixing epoxy.
- Sandpaper to sand down the Tesla logo tab.
#1. How to Replace the 3d Maxpider Logo?
Before starting, check if your logo can fit inside the imprint the 3d Maxpider logo occupied before.
- After removing the 3d Maxpider logo, mix up the epoxy and apply it to the leftover holes. Filling the holes will ensure that the mat won’t leak.
- Get the Tesla logo tab and sand down the bottom. This act will provide a rough grit so the epoxy can glue nicely to the tab.
- Apply saran wrap on a cutting board and place it under the mat. The cutting board is a dense base for the logo to attach.
- Smear epoxy on the bottom of the logo. Make sure to smear within the tab and leave the sides, so the epoxy doesn’t spill when fixed.
- Carefully fix the new tab into the impression. Find something heavy to place on the logo so the epoxy can dry.
Things to Consider During 3d Maxpider Logo Removal
Before removing the 3d Maxpider logo, the first thing to consider is the likelihood of voiding the warranty.
Maxpider floor mat manufacturer does not recommend that you remove the emblem on their floor liners.
When you remove the logo, the company considers the action a modification.
Therefore, you risk losing guaranteed coverage when you remove the logo.
Here are some of the 3d Maxpider Warranty you’ll lose if you remove the logo.
| Warranty Type | Transferability |
|---|---|
| Three years limited warranty. | Non-transferrable |
| Coverage on flaws in products and workmanship. | Transferable |
The above warranty is only applicable if you buy the 3d Maxpider from authorized dealers.
Furthermore, before removing the logo, you must contemplate if you want to leave holes in your floor mat.
Removing the 3d logo on the mat will open holes where water can leak unto the carpet. You must be ready for this reality if you want the logo gone.
Also, you can damage the floor mat by trying to remove the logo. The logo might frustrate you so much that you try to remove it forcibly.
You can scratch or even tear holes through the mat if you don’t execute the removal delicately.
You can end up unintentionally scaring the mat and having a worse situation than when only the logo was there.
Therefore, before you continue with the removal, remember to be gentle in execution.
If you remove the logo, you will have an impression on the mat. In the end, the impression might look worse than the logo itself.
It would be best if you considered using a black sharpie to paint the logo black.
Painting it to match the floor mat’s color is an excellent option. This way, you won’t have to deal with any regrets after removal.
Best Way to Remove 3d Maxpider Logo?
The best way to remove the 3d Maxpider logo is to use a plier. Please take out the mat and turn it upside down.
Grab one of the metal buttons with the plier and pull back and forth until the metal eventually breaks off.
Repeat the process with the other button, and the logo will come off. You can seal any hole in the floor mat using glue, epoxy, or black silicone sealant.
Why 3d Maxpider Logo On Tesla?
Some of the Tesla cars don’t come with floor liners installed in them.
Models like the Tesla SR+, Tesla Model 3, and Tesla Model Y don’t have floor liners. U-Ace, Inc. is a company that makes Maxpider customized floor mats.
They make custom-fit floor mats for various vehicle brands, and Tesla is one of them.
That’s why there is a 3d emblem on the floor liners in Tesla vehicles. Below are some fantastic attributes why Tesla chose these Maxpider floor mats.
#1. Slip Resistance
These Maxpider floor liners have an original anti-skid coat underneath.
Mats from other manufacturers utilize anti-slip points that can create marks on the vehicle’s floor.
Maxpider mats do not cause any marks but remain in place when in use.
#2. Raised Lips
Mats from Maxpider have raised lips. This feature makes them better at holding spills and sand and keeps them away from the car’s floor.
#3. Quality
With Maxpider floor mats, you’re guaranteed quality. The mats undergo high-grade technology.
These floor liners can go on for years without developing fissures or curls.
#4. Design
Despite being very practical, these Maxpider floor mats are stylish and unique in design. They don’t look at odds with your vehicle’s interior and fit right in.
#5. An Easy Clean
It is easy to clean mud, sand, or anything spilled unto Maxpider mats.
The texture of the mat makes it simple for wiping. You can easily shake off any mess on Maxpider floor mats.
Another feature Maxpider mats have is that they are odorless. You won’t perceive any unpleasant whiffs from these mats.
These mats also act as noise dampeners; they reduce road noise as you drive.
In addition, Maxpider mats have a warranty; there is a replacement for anyone with defects.
Conclusion
To remove the 3d Maxpider logo, you need a set of pliers to pry out the metal buttons.
You can fill up the holes in the mat with glue or epoxy. Removing the 3d logo will void any warranty on the Maxpider floor mat.
